Atributy
- Caliber:
375 Caliber (.375)
- Dodací hmotnost: 0,023kg
- Výška přepravy: 1mm
- Šířka přepravy: 83mm
- Délka přepravy: 146mm
Produkt č.: 749011495
Výrob. č.: G375
Měřiče délky komory Sinclair jsou navrženy tak, aby si ruční nabíječ mohl určit skutečnou délku komory své pušky při měření od čela závorníku až po konec krčku komory. Toto měření vám řekne, kolik nadměrné délky nábojnice může vaše komora mít oproti publikovaným trimovacím délkám v příručkách pro ruční nabíjení. Měřiče Sinclair se zasunou do vystřelené, neprimované zkrácené nábojnice a poté se zařadí do vaší pušky. Vložka se při kontaktu s koncem vaší komory vrátí zpět do nábojnice. Poté vytáhnete nábojnici a změříte celkovou délku. Měřič je vyroben z měkké oceli 12L14, takže nepoškodí vaši komoru. K každému měřiči jsou přiloženy podrobné pokyny. Měřiče lze používat znovu a znovu. Rozdíly mezi publikovanými trimovacími délkami a skutečnou délkou vaší komory mohou být velmi významné. Můžete své nábojnice přetrimovávat o .030 palce nebo více. POZNÁMKA: Měřič ráže 22 nebude fungovat na tenkostěnných nábojnicích, jako je 22 Hornet, 218 Bee nebo náboje založené na těchto nábojnicích. Měřič ráže 30 nebude fungovat na 30-30 Winchester. Žádný z uvedených měřičů nebude fungovat na komorách s těsným krčkem, kromě G-243T. Nesmí být používán v pistolích, samonabíjecích puškách, puškách s pákovým mechanismem a puškách s pumpovacím mechanismem.Dodací lhůta je přibližně 14-21 dní.
The Sinclair Chamber Length Gauge is an essential tool for handloaders looking to accurately determine the true length of their rifle's chamber.
The Sinclair Chamber Length Gauges are designed to help you measure from the bolt face to the end of the chamber's neck. This measurement is crucial as it indicates how much excess case length your chamber may have over the published trim lengths found in reloading handbooks.
To use the gauge:
The gauge is made of 12L14 soft steel, ensuring that it will not damage your chamber. Each gauge comes with step-by-step instructions, and they can be reused multiple times.
It's important to note that the differences between published trim lengths and the actual length of your chamber can be significant. Over-trimming your cases by .030 inch or more is possible if you're not using a gauge.
NOTE: The 22 caliber gauge will not work on thin-necked cases such as the 22 Hornet, 218 Bee, or cartridges based on these cases. The 30 caliber gauge is not compatible with the 30-30 Winchester. Additionally, none of the gauges listed will work on tight-necked chambers except for the G-243T. These gauges should not be used in handguns, semi-automatic rifles, lever-action rifles, or pump-action rifles.
375 Caliber (.375)
5.56 NATO gaged Chamber length new DPMS 10.9.2016
Followed instructions as provided and measured the chamber 3 times and the length came out exactly 1.781 on the chamber. Knowing this I will size all my Lake City brass to 1.771. Which is where the vast major of measures to any way. Now I have confidence in my reloads thanks to this marvelous little cheap gage. I will keep all my brass separate and will use the 1.771 brass for match shooting and everything else for plinking.
Worked great 24.12.2015
I had no trouble making a case to accept this gauge. I'm not sure why so many reviewers had difficulties. To make this easier for you gents, trim a re-sized case to 1.640 then insert the gauge. Yes, the case looks short and only has a little bit of neck left, but it works great!
One thing I would change about the directions....it says to drill out the flash hole to make access to push the gauge back out. This is not needed. I used a kinetic bullet puller to "lengthen/re-set" the case with gauge installed. It only needs to be lengthened by 10 thou between uses.
Narazili jsme na chybu při načítání obsahu. Obnovte stránku a zkuste to znovu. Pokud problém přetrvává, kontaktujte naši zákaznickou podporu.