Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Vylepšete svůj pistol s montáží S&W M&P TRIJICON RMR SIGHT MOUNT od EGW!
Materiál: 7075 hliník
Úprava: Matný černý tvrdý povlak
Celková délka: 1.780"
Celková šířka: 1.1"
Montážní hardware: (2) 6-32 ploché šrouby, (1) 6-32 x 3/16 šroub
Kompatibilita s červeným bodem: Trijicon RMR
Tato montáž je kompatibilní s:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
Tato montáž není kompatibilní s:
- Smith & Wesson M&P Shield (Naše montáž je příliš široká na Shield)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Nebude fit pro M&P .22 Compact. Dovetail zadních mířidel Smith & Wesson se mohou lišit v rozměrech. Naše mířidla jsou vyrobena s ohledem na stejné tolerance. Někteří uživatelé mohou mít potíže s instalací naší desky na jejich závěrce kvůli různým tolerancím ve vašich závěrkách. Mějte to prosím na paměti při objednávání.
Tato montáž by měla být instalována a kontrolována kvalifikovaným zbrojířem. Za poškození nebo zranění, které může vzniknout nesprávnou instalací nebo používáním tohoto produktu, neneseme žádnou odpovědnost.
Jednoduše odstraňte zadní mířidlo na vaší zbrani a nahraďte ho naší montáží, abyste mohli namontovat váš Trijicon RMR červený bod. Nejsou vyžadovány žádné úpravy. Naši montáž můžete kdykoliv sundat a nahradit své zadní mířidlo. Montážní hardware je součástí balení.
Pokyny k instalaci:
- Odstraňte zadní mířidlo*
- Instalujte EGW Sight Mount do dovetailu
- Pevně utáhněte šroub (pokud je to relevantní)
- Položte červený bod na EGW Sight Mount (umístění malého kousku papíru mezi červený bod a montáž usnadní odstranění a udrží Loctite mimo červený bod).
- Naneste modrý Loctite na dodané montážní šrouby
- Utáhněte montážní šrouby na 15in/lbs
*Nástroj na posun zadního mířidla je velmi doporučen.