Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Vylepšete svůj zrakový systém s montáží EGW pro RUGER PC CARBINE.
Materiál: 7075 Aluminum
Povrchová úprava: Matte Black Hardcoat
Celková délka: 1.811"
Celková šířka: .99"
Montážní hardware:
- (2) 6-32 Button Head Screws
- (2) 6-32 Flat Head Screws
- (1) 6-32 Set Screw
Kompatibilita s red dot: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter
Montáže EGW pro red dot jsou určeny k instalaci zleva doprava (s hlavní směřující dopředu). Dovetail má progresivní zúžení pro snadnější instalaci.
Jednoduše odstraňte zadní mířidlo na vaší zbrani a nahraďte ho naší montáží pro instalaci red dot optiky Vortex Viper/Venom, Burris FastFire nebo Docter. Není potřeba žádných úprav. Naši montáž můžete kdykoli odstranit a vrátit zpět zadní mířidlo. Montážní hardware je součástí balení.
Pokyny k instalaci
- Odstraňte zadní mířidlo*
- Instalujte EGW Sight Mount do dovetailu
- Utáhněte set screw (pokud je to relevantní)
- Položte red dot sight na EGW Sight Mount (umístění malého kousku papíru mezi red dot sight a sight mount usnadní odstranění a udrží Loctite mimo red dot sight)
- Naneste modrý Loctite na dodané montážní šrouby
- Utáhněte montážní šrouby na 15in/lbs
2 Button Head Cap Screws - Dodáno pro Vortex Viper a Venom Sights
2 Flat Head Cap Screws - Dodáno pro Burris FastFire a Docter Sights
Šrouby, které jsou součástí této montáže, vyžadují imbusový klíč velikosti 5/64'' pro instalaci.