OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) is the latest member of the OPF line. G43x and 48 MOS slides are designed for direct mounting of the Shield RMSc sight. Trijicon's RMRcc is longer, and requires an adapter plate which also necessarily raises the mounting surface in order to mount an RMRcc. RMRcc has its own footprint. Gone are the two lug holes in front, these are replaced by two larger diameter threaded posts (bosses) through which the sight to mount/plate screws are installed. The sight to mount/plate screws are also significantly strengthened, though with the OPF-G, RMRcc design that holds the sight immobile on the plate, the larger diameter and stronger screws aren't as important, we always welcome screws that are less likely to strip. With the OPF-G43x/48, RMRcc, we didn't merely raise the mounting surface to provide a platform for the RMRcc. As RMRcc is longer than the G43X/48 MOS cut, the sight overhangs on the slide. When installed, the bottom of RMRcc (with Trijicon provided sealing plate installed) is almost flush with the top of the slide so the sight is as low as possible. We positioned the RMRcc towards the center of the plate as much as feasible, this is done to reduce the amount of unsupported overhang on the RMRcc's sealing plate in front. RMRcc has a rubber gasket around its battery compartment to keep water and moisture at bay, which pushes the sealing plate downward. This isn't an issue if the plate is of the same length as the RMRcc, but with an overhang, it creates a slight gap between the gasket and the sealing plate. OPF-G43x/48, RMRcc's design eliminates the gap/opening between the sight and sealer plate, to the point of emulating a plate that's as long as the sight itself. To wit, if the plate is as long as the RMRcc, it will make the installed height of RMRcc even taller, which is the very reason we chose to let the sight overhang. Torque value: Plate to slide: 12 to15 in·lbs. Sight to plate: 18 in·lbs.. Weight: 0.75oz Material: 1018 steel, black nitrided
Adaptér pro Trijicon RMRcc na Glock 43/48 - ideální řešení pro montáž optiky!
OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) je nejnovějším členem řady OPF. Slidy G43x a 48 MOS jsou navrženy pro přímou montáž optiky Shield RMSc. RMRcc od Trijicon je delší a vyžaduje adaptér, který také nezbytně zvyšuje montážní plochu pro upevnění RMRcc. RMRcc má svůj vlastní profil.
Na přední straně již nejsou dva otvory pro šrouby, tyto jsou nahrazeny dvěma většími závitovými sloupky (bossy), skrze které jsou instalovány šrouby pro montáž optiky. Šrouby pro montáž jsou také výrazně posílené, i když s designem OPF-G, který drží optiku na desce pevně, nejsou větší průměr a silnější šrouby tak důležité; přesto vždy vítáme šrouby, které se méně pravděpodobně poškodí.
U OPF-G43x/48, RMRcc jsme nezvýšili pouze montážní plochu pro RMRcc. Protože je RMRcc delší než výřez G43X/48 MOS, optika přesahuje přes slid. Po instalaci je spodní část RMRcc (s instalovanou těsnicí deskou od Trijicon) téměř v rovině s vrcholem slid, takže optika je co nejníže. RMRcc jsme umístili co nejvíce do středu desky, abychom snížili množství nepodporovaného převisu na těsnicí desce RMRcc vpředu.
RMRcc má gumovou těsnění kolem svého prostoru pro baterii, aby udržel vodu a vlhkost na uzdě, což tlačí těsnicí desku dolů. To není problém, pokud je deska stejně dlouhá jako RMRcc, ale s převisem vzniká mírná mezera mezi těsněním a těsnicí deskou. Design OPF-G43x/48, RMRcc eliminuje mezeru/otvor mezi optikou a těsnicí deskou, až do bodu, kdy napodobuje desku, která je stejně dlouhá jako samotná optika.
Pokud je deska stejně dlouhá jako RMRcc, zvýší to výšku instalace RMRcc, což je důvod, proč jsme se rozhodli nechat optiku přesahovat.
- Hodnota utahovacího momentu: Deska k slid: 12 až 15 in·lbs.
- Optika k desce: 18 in·lbs.
- Hmotnost: 0.75 oz
- Materiál: 1018 ocel, černě nitridovaná