Brownells Česká republika - Světově největší dodavatel součástek zbraní, zbrojního vybavení a příslušenství. Česká republika

EGW
BROWNING BAR / BLR LONG ACTION HD PICATINNY SCOPE MOUNT

841370114139 296000768
EGW recommends measuring the hole spacing in your receiver to confirm it matches with the dimensions they have published. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. EGW machines these in their shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type III anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is sold separately). Recommend: 0 MOA - if shooting 0-500 yards 20 MOA - if shooting 500-1000 yards When zeroing your rifle with a 20 MOA mount, EGW recommends zeroing at 200 yards. The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA. This Mount Fits: Browning BAR (all calibers) Browning BLR Long Action Browning BLR Takedown Browning BPR Browning Short Trac Benelli R1* (see below) This Mount Does Not Fit: Browning BAR MK3 DBM - This rifle has integrated picatinny style rails that are not removable In October 2019 the overall length of this mount was changed from 5.488"" to 5.094"" to accomodate takedown models.  If you purchase a mount from a third party seller there is a chance it may be older and not fit your takedown. *This mount will fit the Benelli R1 Rifles. It will cover the middle hole on their action, but will use the front and back pairs.   ***This mount does not fit the BAR ShortTrac Hog Stalker. EGW does not have a mount that works with this application. EGW has found that older model BLRs may use the long action rail despite the caliber. Please measure your hole spacing to confirm.
1999 1999 1 CZK
New
Produkt č.: 296000768
EGW BROWNING BAR/BLR LA 1-PIECE PICATINNY BASE 0 MOA
Číslo výrobce: 81029 841370114139 EGW doporučuje změření rozteče otvorů ve vaší zbrani, aby se potvrdilo, že odpovídá zveřejněným rozměrům. Picatinny drážky běží po celé délce lišty, což střelci poskytuje flexibilitu při montáži kroužků puškohledu a dalších příslušenství. Kanál uprostřed snižuje celkovou hmotnost montáže. V mnoha případech také neblokuje použití továrních železných mířidel. Jednodílné montáže puškohledu od EGW jsou zřejmou volbou pro lovce i taktické střelce. EGW tyto montáže obrábí ve své dílně s použitím obráběcích center. Po obrábění jsou montáže tříděny, pískovány a anodizovány typem III pro dlouhou trvanlivost. Instalace: EGW doporučuje použít moment 20 inch lbs a kapku modrého loctite (loctite je prodáváno zvlášť). Doporučení: 0 MOA - pro střelbu na 0-500 yardů 20 MOA - pro střelbu na 500-1000 yardů Při nulování vaší pušky s montáží 20 MOA doporučuje EGW nulování na 200 yardů. Celá montáž a příslušenství (od montážních šroubů a klíče až po obal) jsou vyrobeny v USA. Tato montáž pasuje na: Browning BAR (všechny ráže) Browning BLR Long Action Browning BLR Takedown Browning BPR Browning Short Trac Benelli R1* (viz níže) Tato montáž nepasuje na: Browning BAR MK3 DBM - Tato puška má integrované picatinny lišty, které nelze odstranit V říjnu 2019 byla celková délka této montáže změněna z 5.488" na 5.094", aby vyhovovala modelům pro rozložení. Pokud si zakoupíte montáž od prodejce třetí strany, je možné, že bude starší a nebude pasovat na váš model pro rozložení. *Tato montáž se hodí na pušky Benelli R1. Zakryje střední otvor na jejich závěru, ale bude používat přední a zadní dvojici otvorů. ***Tato montáž není kompatibilní s BAR ShortTrac Hog Stalker. EGW nemá montáž, která by byla s tímto modelem kompatibilní. EGW zjistilo, že starší modely BLR mohou používat lištu pro dlouhou akci bez ohledu na ráži. Prosím, změřte rozteč otvorů, abyste potvrdili.
1999 CZK 10 1 999,00 Kč *
Dodací lhůta je přibližně 14-21 dní.
Více než 10 ks. skladem USA
Vlastnosti: Action Type: Long Barevný: Black Elevation: 0 MOA Make: Browning Material: Aluminum Model: BLR, BAR Number of Bases: 1-Piece Style: Picatinny lišta

Atributy

Action Type: Long Color: Black Elevation: 0 MOA Material: Aluminum Model: BLR,BAR Number of Bases: 1-Piece Style: Picatinny lišta Udělat: Browning Dodací hmotnost: 0,091kg Výška přepravy: 25mm Šířka přepravy: 102mm Délka přepravy: 229mm

Detail produktů

Made in USA



EGW recommends measuring the hole spacing in your receiver to confirm it matches with the dimensions they have published. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. EGW machines these in their shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type III anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is sold separately). Recommend: 0 MOA - if shooting 0-500 yards 20 MOA - if shooting 500-1000 yards When zeroing your rifle with a 20 MOA mount, EGW recommends zeroing at 200 yards. The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA. This Mount Fits: Browning BAR (all calibers) Browning BLR Long Action Browning BLR Takedown Browning BPR Browning Short Trac Benelli R1* (see below) This Mount Does Not Fit: Browning BAR MK3 DBM - This rifle has integrated picatinny style rails that are not removable In October 2019 the overall length of this mount was changed from 5.488"" to 5.094"" to accomodate takedown models.  If you purchase a mount from a third party seller there is a chance it may be older and not fit your takedown. *This mount will fit the Benelli R1 Rifles. It will cover the middle hole on their action, but will use the front and back pairs.   ***This mount does not fit the BAR ShortTrac Hog Stalker. EGW does not have a mount that works with this application. EGW has found that older model BLRs may use the long action rail despite the caliber. Please measure your hole spacing to confirm.
Novinky