Košík je prázdný.

Košík

Novinky

308 AR HANDGUARD REMOVAL TOOL

050806108554 080000487

Makes Taking The Handguard Off Fast, Easy & Painless

Handy tool eliminates the need for a second pair of hands when removing AR-type handguards. Simply insert the hooked end of the tool into the mag well, position handles over delta ring, and push down to compress the delta ring spring. Made of strong ¼" (6.4mm) steel rod, with synthetic rubber coating to protect gun from surface scratches.

SPECS: Steel, rubber-coated, black. 11” (27.9cm) long. Fits AR-15, M16A1 & A2, and AR-Style .308 rifles with delta rings.

Další...

Demontáž předpažbí rychlá, snadná a bezbolestná

Praktický nástroj eliminuje potřebu dalšího páru rukou při demontáži předpažbí typu AR. Jednoduše vložte háčkovaný konec nástroje do magazínové studny, umístěte rukojeti přes delta kroužek a stlačte dolů k zatlačení pružiny delta kroužku. Vyrobeno z pevné ¼" (6,4 mm) ocelové tyče, s povrchovou ochranou z syntetické pryže, aby nedošlo k poškrábání povrchu zbraně.

SPECS: Ocel, pogumovaná, černá. 11” (27,9 cm) dlouhá. Vhodná pro AR-15, M16A1 & A2 a AR-Style .308 pušky s delta kroužky.

Další...

Hodnocení zákazníků pro položku BROWNELLS AR-15/M16 HANDGUARD REMOVAL TOOL

Počet hodnocení: 13
Od brownells.com: 13
Průměrné hodnocení: 3

Works fantastic. (13.9.2009)

Makes removing or replacing handguards easy.
Protective coating prevents scratching or damaging finish of firearm. Plenty of surface area making contact with magazine well to distribute stress levels below damage levels. And yes there are some out there on the market that do not have a protective coating and a small contact point that can cause indentation (dents) in your Mag well. Great product!

great!! (15.9.2009)

Makes a world of difference. No more fighting to get the handguards off.

Not all it's cracked up to be (18.11.2009)

After removing the handguard on only one rifle, the coating is broken through at the contact points with the delta ring. Even before this, the coating is not bonded to the wrench underneath and rotates around, losing much of the extra leverage it could otherwise be providing.

I will probably improve mine by removing the existing coating and replacing with an industrial, hot-glued heat shrink insulation.

Worked But Protective Covering Came Off (18.2.2010)

While trying to install some new Troy rails on my Colt M4 I used this tool and the rubberized protective covering on the removal tool ripped and started coming off. I would not recommend this tool until a different rubberized treatment was applied to the tool.

overall good tool (15.3.2010)

Makes the job of removing the handgurds very easy. Very easy on the hands. Rubber protective coating is a bit soft and is heavily scuffed after limited use. It is not torn and no metal is exposed but still reveals a minor lack of quality. Not too hard to upgrade on your own for the price value here though.

coating comes off after a few uses (25.4.2010)

Have only used a few times and the urethane coating has broken and is coming off at all contact points. Great for a single build but not for folks who want to use it for several.

Does What It Needs To (6.8.2010)

I used this tool to remove the factory handguard on my AR carbine. It worked perfectly, without any problems. It is much better than trying to remove a handguard without any tools. Save yourself the hassle and purchase this tool.

Worked good for one use (8.3.2012)

Product works like it is supposed to. Problem is the coating is already crinkled after one use. I would recomend wrapping it in black electrical tape to help sustain the coating.

"Serious Users Need Not Apply" (5.4.2012)

This is almost not worth getting... it is only good for 1 or 2 uses before the coating is worn out. Once the rubber wears away it will scratch up the delta ring and is almost impossible to keep it from slipping.
Case and point: 3rd rifle I tried with this in the first day of use it slipped off a brand new stubborn/tight delta ring and my knuckles suddenly lacked skin from impacting the receiver with the force I was applying to the tool.
For such limited use I would stick to manually removing the handguard by hand.. that being said if your like me and work on multiple AR's a week then you need something beefier. This wont cut it for any long term armorer duty. Save yourself the cash and just buy the stronger model that costs a bit more on here. Night and day difference and that one is actually going strong many rifles later.

Must have tool (13.8.2012)

Very handy tool with new delta ring springs, speeds up hand guard installation.

Damages Gun (20.1.2014)

Used one time and the plastic coating on the tool is so cheap that it it pushed right through to the finiish on the underside of the magazine. Left about 1/2 centimeter gouge out of the gun's black finish. Total junk. Do not buy, look for fully pollymer alternatives or tightly rubberband two tooth brushes together facing away frome one another. Works just and well and wont scratch your weapon.

Don't get this one! (29.11.2015)

First use coating came off, slipped down and marred finish. Horrible. Pay the extra few bucks and get the other one here. You wont be sorry.

priced right, easily improved (30.4.2018)

i originally purchased a significantly more expensive tool for this purpose, and it looked like it had been made by a twelve year old industrial arts student. this thing turns out to be among the least expensive of its type, has symmetrical bends, no sketchy welds, and is sufficiently stout for careful use right out of the box.

a bunch of folks have dumped on this tool for the coating peeling where it contacts the delta ring. to be safe, i found a short section of â"id vinyl tubing, and chopped off a couple of 3" lengths. they slipped right over the dipped coating already on the tool, and the thing functions flawlessly. if the magwell end of the tool ever starts to go, i'll slap some heavy shrink tube on it and it will be fine.

5 minutes of work has made this thing as good as or better than tools that cost twice the price.

Přečtete si další hodnocení na webu brownells.com

949 949 1 CZK

Produkt č.: 080000487
BROWNELLS AR-15/M16 HANDGUARD REMOVAL TOOL 050806108554 Praktický nástroj eliminuje potřebu dalšího páru rukou při demontáži předpažbí typu AR. Jednoduše vložte háčkovaný konec nástroje do magazínové studny, umístěte rukojeti přes delta kroužek a stlačte dolů k zatlačení pružiny delta kroužku. Vyrobeno z pevné ¼" (6,4 mm) ocelové tyče, s povrchovou ochranou z syntetické pryže, aby nedošlo k poškrábání povrchu zbraně.

949 CZK 0 949,00 Kč *

Předbjednávka, dodací lhůta je přibližně 4-12 týdnů ze skladu z USA.

Vlastnosti: Make: AR-15

Vložit do nákupního seznamu

Zeptejte se

Podrobnosti

Vložit do nákupního seznamu

Zeptejte se

Atributy

Udělat: AR-15 Dodací hmotnost: 0,113kg Výška přepravy: 41mm Šířka přepravy: 99mm Délka přepravy: 292mm

Detail produktů

Made in USA

Makes Taking The Handguard Off Fast, Easy & Painless

SPECS: Steel, rubber-coated, black. 11” (27.9cm) long. Fits AR-15, M16A1 & A2, and AR-Style .308 rifles with delta rings.

Další...

Demontáž předpažbí rychlá, snadná a bezbolestná

SPECS: Ocel, pogumovaná, černá. 11” (27,9 cm) dlouhá. Vhodná pro AR-15, M16A1 & A2 a AR-Style .308 pušky s delta kroužky.

Další...

Hodnocení zákazníků pro položku BROWNELLS AR-15/M16 HANDGUARD REMOVAL TOOL

Počet hodnocení: 13
Od brownells.com: 13
Průměrné hodnocení: 3

Works fantastic. (13.9.2009)

great!! (15.9.2009)

Makes a world of difference. No more fighting to get the handguards off.

Not all it's cracked up to be (18.11.2009)

Worked But Protective Covering Came Off (18.2.2010)

overall good tool (15.3.2010)

coating comes off after a few uses (25.4.2010)

Have only used a few times and the urethane coating has broken and is coming off at all contact points. Great for a single build but not for folks who want to use it for several.

Does What It Needs To (6.8.2010)

Worked good for one use (8.3.2012)

Product works like it is supposed to. Problem is the coating is already crinkled after one use. I would recomend wrapping it in black electrical tape to help sustain the coating.

"Serious Users Need Not Apply" (5.4.2012)

Must have tool (13.8.2012)

Very handy tool with new delta ring springs, speeds up hand guard installation.

Damages Gun (20.1.2014)

Don't get this one! (29.11.2015)

First use coating came off, slipped down and marred finish. Horrible. Pay the extra few bucks and get the other one here. You wont be sorry.

priced right, easily improved (30.4.2018)

Přečtete si další hodnocení na webu brownells.com

Zákazníci také kupují
Alternativní produkty

J P ENTERPRISES TUNED BUFFER SPRING, CARBINE
AR-15/M16/308 AR TUNED BUFFER SPRING

J P ENTERPRISES

Skladem

999,00 Kč * 999,00 Kč - 1 099,00 Kč*

Vratné pružiny

4,9

New

AR15.COM 2.5" BOLT FACE LOGO PATCH TAN
2.5" BOLT FACE LOGO PATCHES

AR15.COM

Neznáma dostupnost

IOSSO PRODUCTS AR-15 BRUSH PAK
AR-15/M16 ELIMINATOR™ AR-15 BRUSH PAK

IOSSO PRODUCTS

Skladem

699,00 Kč *

Kartáče na pistole

IOSSO PRODUCTS IOSSO RIFLE BRUSH .30, .308 CAL
IOSSO NYFLEX RIFLE BORE BRUSHES

IOSSO PRODUCTS

Skladem

289,00 Kč * 279,00 Kč - 299,00 Kč*

Čistící kartáčky

IOSSO PRODUCTS IOSSO PISTOL BORE BRUSH .22 CAL
IOSSO NYFLEX PISTOL BORE BRUSHES

IOSSO PRODUCTS

Skladem

299,00 Kč * 289,00 Kč - 299,00 Kč*

Čistící kartáčky

Přihlášení

Zapomněli jste heslo?
Zaregistrovat se

Sociální média

Facebook

Mapa stránky

Produktové Kategorie

Objednávaní

Zákaznícký servis

Společnost Brownells je předním světovým dodavatelem zbrojních nástrojů, dílů střelných zbraní a jejich příslušenství, která je na trhu již více než 75 let. S důvěrou se na nás obrací laická i odborná veřejnost.

Internetový obchod Vám nabízí více než 52 000 produktů, ze kterých si vybere i ten nejnáročnější uživatel.

Vaše spokojenost je pro nás velmi důležitá. Proto se snažíme neustále rozšiřovat portfolio produktů. Může se stát, že se zbožím nebudete spokojeni, můžete ho kdykoliv vrátit a dostanete od nás zpět plnou částku nebo nový produkt v uvedené hodnotě.

Chceme být zárukou Vaší spokojenosti!

cf-web-badges-e-ltgray