Atributy
- Make: -
- Dodací hmotnost: 0,023kg
- Výška přepravy: 3mm
- Šířka přepravy: 3mm
- Délka přepravy: 3mm
- UPC: 050806007307
Produkt č.: 080001118
050806007307 Precizně zpracovaný, solidní ocelový nástroj umožňuje bezpečné zajištění šroubů klíče nosiče nejlepším způsobem - z boku - aby se zajistilo, že se neuvolní ani za nejextrémnějších podmínek rychlopalby. Odstraňuje potíže s pokusy o zajištění šroubů kladivem a razníkem, které by mohly sklouznout a poškodit klíč, šrouby nebo nosič. Nástroj pevně drží nosič a umisťuje klíč tak, aby mohl být prohlouben na správných místech utažením čtyř šestihranných šroubů na nástroji. Další zajišťovací šroub na vrchu nástroje zabraňuje pohybu nosiče. Hrot tohoto šroubu je opracován plochý, aby se zajistilo rovnoměrné udržovací síly a aby nedošlo k poškození nosiče. Všechny hroty šroubů jsou kaleny na Rc 58-62 pro trvanlivost; nicméně, někdy se šrouby mohou zlomit, proto nabízíme 4-pak náhradních šroubů.Dodací lhůta je přibližně 14-21 dní.
Precision-machined, solid steel tool lets you stake the carrier key screws the best way—from the sides—to ensure they don't back out under the most strenuous rapid-fire conditions. Eliminates the hassle of trying to stake the screws with a hammer and punch that could slip and damage the key, screws, or carrier.
Not the best of it's type. 3.3.2016
My agency has this tool. I am a COLT LE armorer with extensive .mil and .le experience with the platform, as well as extensive personal experience and ownership. After staking four gas keys, my issues with this tool are:
1. Stakes too high on gas key. This results in very sharp edges and a questionable amount of material impinging on the screws. The staking bolts' points actually are forced higher when turning them into the gas key.
2. Staking mechanism (sharpened, hardened allen bolts) are too sharp and actually cut the metal, versus deforming it. Again, sharp edges and too little material left to impinge on screws. Further, it really destroys the finish, leaving bare metal.
3. The tool's alignment is off a bit, resulting in very slightly off-centered (versus gas key screw axis) stakes.
If you expect MilSpec-like results, IMO this is not the answer. The stakes will look amateurish and butchered, versus what is seen on a Colt factory-staked gas key. It is likely serviceable with regards to doing the job, however, and probably better (and faster) than a hammer and punch for most folks. But for serious use, look elsewhere, such as the MOAKS tools from Ned Christiansen. I have no affiliation and don't own his product at this time, but I have used it in the past with success. We chose the Brownells unit because it was easily to purchase with our existing account, but I can't recommend it to others at this time.
Note, images show a BCG that was staked 15 minutes ago. Bare metal highlights on edges are from stoning to reduce the sharp burrs from the Brownells tool, which was necessary even after light peening with a small hammer.

Excellent tool 18.11.2012
Puchased this to re-stake all of my departments long gun bolts as they had not been staked properly from the factory and the gas key had come loose on several rifles. This is a very heavy duty staking tool and I was able to stake 15 + keys with no problem. I have also used the staking points to stake other parts on the rifle such as the castle nut. Simply unscrew them and use a hammer to stake them. I highly recommend this product.
Narazili jsme na chybu při načítání obsahu. Obnovte stránku a zkuste to znovu. Pokud problém přetrvává, kontaktujte naši zákaznickou podporu.