Přes 300 000 zákazníků - děkujeme vám!

40 000+ produktů pro lov a střelbu

Objevte EXTRACTOR ROD pro více než 2-1/2" hlaveň od Smith & Wesson. 🔧 Ideální pro model K Frame!
  • SMITH & WESSON EXTRACTOR ROD, OVER 2-1/2" BARREL, SS
  • SMITH & WESSON EXTRACTOR ROD, OVER 2-1/2" BARREL, SS
  • SMITH & WESSON EXTRACTOR ROD, OVER 2-1/2" BARREL, SS

SMITH & WESSON EXTRACTOR ROD, OVER 2-1/2" BARREL, SS

940070500

Atributy

  • Model: K Frame
  • Typ zbraně: Smith & Wesson
  • Dodací hmotnost: 0,018kg
  • Šířka přepravy: 83mm
  • Délka přepravy: 146mm

Detail produktů

Made in USA
US exportní klasifikace: 0A501.x
  • Specifikace:
  • Make: Smith & Wesson
  • Model: K Frame
0 0 1 CZK
  • Specifikace:
  • Make: Smith & Wesson
  • Model: K Frame

Popis:

Zobrazit originál (anglicky)
PASUJE: 64-3, .38; 65/65LS, .357; 66, .357; 67, .38; 617, .22; 648, .22 Mag; 681, .357; 686, .357; 696, .44 Spl
EXTRACTOR ROD, OVER 2-1/2" BARREL, SS

Atributy

  • Model: K Frame
  • Typ zbraně: Smith & Wesson
  • Dodací hmotnost: 0,018kg
  • Šířka přepravy: 83mm
  • Délka přepravy: 146mm

Detail produktů

Made in USA
US exportní klasifikace: 0A501.x

Recenze zákazníků

Hodnocení zákazníků (2)

5 / 5
Rozhodně doporučuji

Brownells USA Quality replacement 6.6.2016

Ordered this factory replacement for a badly chewed up one. Came in sealed bag but needed to be cleaned because of very fine metal particles from manufacturing. Used a pipe cleaner to get inside and a used a touch of CLP. Perfect with no fitting required and matched original stainless finish. This went on a 66-2.

Rozhodně doporučuji

Brownells USA Extractor rod replacement for 686 Plus 16.5.2016

I needed to find a replacement extractor rod for my S&W L-frame 686 Plus 4" Stainless revolver. Originally, I searched for this part online and bought a similar extractor rod from another retailer, but the one I received looked like it was used, about to rust and the threads were galled, so I returned it. I later found out Brownells had this part available and so I ordered this one for barrels over 2-1/2" in SS for my 4" 686+. I was pleased to find out that extractor rod came new in the yellow sealed plastic bag. This extractor rod does require some fitting (on the end opposite of the threads where the diamond pattern texturing is) to get the extractor rod to reliably engage and release from the locking bolt. My original extractor rod measured 2.6650” with digital calipers, so I patiently took my time to file the end of the new extractor with my Spyderco ceramic file and continued to remeasure it until the length was the same as my original. It probably took me about a couple of hours to file the extractor rod to spec, then afterwards I gently reamed and deburred the sharp edges. In the end, the extractor rod is a perfect fit with both positive lockup and release.

Věděli jste?

Informace o výrobci

Odpovědný hospodářský subjekt podle nařízení EU

Brownells Arms s.r.o.
Bílanská 1861/81
76701 Kroměříž
Česká republika
info@brownells.cz

Jejda! Něco se pokazilo.

Narazili jsme na chybu při načítání obsahu. Obnovte stránku a zkuste to znovu. Pokud problém přetrvává, kontaktujte naši zákaznickou podporu.

Zpět na začátek