Use To Align Parts, Start Pins, Assembly/Dissambly
For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won’t bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the AR-15, 1911 Auto, Remington 870 and Ruger Revolvers. Won’t roll off bench. Alignment/Push Punch Set includes one each of the punches listed below, plus a Delrin bench block to store and organize all eight punches, so you always have them at your fingertips. Bench block also available separately.
SPECS: Handle - Plastic. Shank - Unhardened steel drill rod, or 360 alloy brass . 3¼” (8.2cm) long. OAL - 4¾” (12.1cm) long. Alignment/Push Punch Set - Contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092” (2.3mm), .120” (3mm), .151” (3.8mm), and .246” (6.2mm). Bench Block - Delrin, tan. 63⁄8” (16cm) long, 3” (7.6cm) wide, ¾” (1.9cm) high. Holds 8 punches.
Počet hodnocení: 3
Od brownells.com: 3
Průměrné hodnocení: 3,7
Handy Set(19.6.2012)
This is a great set and the block makes a nice place to store them on your bench. They are not made to be hammered, but you could lightly tap them with a nylon hammer without damage. The set I bought included steel and brass.
Brownells push pin set(8.6.2017)
I like the brass pin pushers but the steel pin pushers are very soft and will bend easily if you need to align parts.
A Must Have(17.4.2010)
These are great for installing triggers on AR'S. These Brass alignment punches should be on the bench of every gunsmith or hobbyist.
Produkt č.: 080000034 BROWNELLS SET OF FOUR STEEL PUNCHES Tyto údery třeba pro profesionální a domácí dílně, stejně jako mnoho frustrace z zarovnání dílů a sestav. A poskytují rychlejší a snadnější demontáž, taky. Zařízený s velkým, snadno to pochopit, úchyt, který poskytuje vynikající kontrolu pro zarovnání díry a spouštění čepy. Mírně podměrečné dříku zajišťuje Přiléhavý střih, který se nepřipoutává v díře. Mírné zúžení, 3/4 "od konce je obzvláště užitečné při montáži součástek, které vyžadují opakované montáže a demontáže. Čtyři velikosti vhodné pro většinu kolíky nalezené na AR-15, 1911, Auto, Remington 870 a revolvery Ruger. Nebudou sjet z lavice. Zarovnání/Push Punch Set obsahuje jednu údery, níže uvedených, plus blok Delrin lavice k ukládání a uspořádání všech osm úderů, takže budete mít vždy na dosah ruky. Lavička bloku k dispozici také samostatně.
1399CZK01 399,00 Kč
*
Přeobjednáno, dodací lhůta cca 4-12 týdnů ze skladu v USA.
Vlastnosti:Material: SteelSize: .092 in, .120 in, .151 in, .246 inStyle: Set, Alignment, TisknoutMnožství: 4
Use To Align Parts, Start Pins, Assembly/Dissambly
For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won’t bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the AR-15, 1911 Auto, Remington 870 and Ruger Revolvers. Won’t roll off bench. Alignment/Push Punch Set includes one each of the punches listed below, plus a Delrin bench block to store and organize all eight punches, so you always have them at your fingertips. Bench block also available separately.
SPECS: Handle - Plastic. Shank - Unhardened steel drill rod, or 360 alloy brass . 3¼” (8.2cm) long. OAL - 4¾” (12.1cm) long. Alignment/Push Punch Set - Contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092” (2.3mm), .120” (3mm), .151” (3.8mm), and .246” (6.2mm). Bench Block - Delrin, tan. 63⁄8” (16cm) long, 3” (7.6cm) wide, ¾” (1.9cm) high. Holds 8 punches.
Počet hodnocení: 3
Od brownells.com: 3
Průměrné hodnocení: 3,7
Handy Set(19.6.2012)
This is a great set and the block makes a nice place to store them on your bench. They are not made to be hammered, but you could lightly tap them with a nylon hammer without damage. The set I bought included steel and brass.
Brownells push pin set(8.6.2017)
I like the brass pin pushers but the steel pin pushers are very soft and will bend easily if you need to align parts.
A Must Have(17.4.2010)
These are great for installing triggers on AR'S. These Brass alignment punches should be on the bench of every gunsmith or hobbyist.