Přes 300 000 zákazníků - děkujeme vám!

40 000+ produktů pro lov a střelbu

Simulated selector lever for M14 stocks gives a full-auto look, fills gaps, keeps debris out, and installs legally on the stock with minor fitting required.
  • FULTON ARMORY SIMULATED SELECTOR LEVER
  • FULTON ARMORY SIMULATED SELECTOR LEVER
  • FULTON ARMORY SIMULATED SELECTOR LEVER

FULTON ARMORY SIMULATED SELECTOR LEVER

100005279

Atributy

  • Model: M14,M1A
  • Typ zbraně: Springfield
  • Dodací hmotnost: 0,045kg
  • Výška přepravy: 23mm
  • Šířka přepravy: 71mm
  • Délka přepravy: 135mm

Detail produktů

Made in USA
US exportní klasifikace: 0A501.x
  • Specifikace:
  • Make: Springfield
  • Model: M14, M1A
0 0 1 CZK

Popis:

Zobrazit originál (anglicky)

Vytvořte autentický vzhled pro váš poloautomatický pušku!

Jednodílná simulovaná páka pro výběr, vyrobená z parkovaného oceli, se hodí do výřezu pro páku výběru v USGI a aftermarket M14 pažbách, aby vaše puška měla autentický vzhled pušky GI M14 schopné plně automatického režimu. Zaplní nevzhlednou mezeru a pomáhá udržovat nečistoty a nečistoty mimo mechanismus.

Vlastnosti produktu:

  • Materiál: Ocel, parkovaná, matně černá
  • Kompatibilita: Pasuje na USGI a aftermarket M14 pažby s výřezem pro páku výběru
  • Montážní hardware: Součástí balení
  • Požadované úpravy: Menší úpravy mohou být potřeba

Páka se otáčí do polohy poloautomatického nebo plně automatického režimu. Instalace se provádí na pažbě, nikoli na přijímači, což je zcela legální.



Atributy

  • Model: M14,M1A
  • Typ zbraně: Springfield
  • Dodací hmotnost: 0,045kg
  • Výška přepravy: 23mm
  • Šířka přepravy: 71mm
  • Délka přepravy: 135mm

Detail produktů

Made in USA
US exportní klasifikace: 0A501.x

Recenze zákazníků

Hodnocení zákazníků (5)

4,2 / 5
Doporučuji

Brownells USA Why mess with epoxy? 25.3.2016

The simulated selector lever dropped right in on my walnut GI M14 stock. Make sure you use the correct size drill bits for drilling into the stock for the screw and pin. I used the selector as a template and drilled the hole for the screw mount first then slightly screwed in the mounting screw into the stock to hold the selector in place. Next I drilled the pin hole into the stock to the appropriate depth and lightly tapped the pin into place with my brass faced punch hammer. Then tightened the wood screw to complete the install. The final results are a much more professional/realistic looking vs the epoxy fillers that never match the stock

Doporučuji

Brownells USA I love this but.... 5.1.2014

Today, we attempted to install 3 of these, we were able to get two to fit. The third one did not fit because we were attempting to use it on a rare Devine Texas M1a. The receiver is different and some metal will need to be removed from the switch. Rule number 1, always modify the cheapest part.

To begin with, no instructions come with the switch. That isn't a bad thing, first see if the switch will fit your rifle by installing it with using the screw and roll pin. If the receiver closes then you are good to go. You can save yourself all kinds of problems by drilling the hole for the roll pin larger, I think that the pin is too big as it comes from the factory.

You are going to have to use a drill no matter what! You need to pre-drill the holes for the roll pin and screw in the wood. Install the roll pin first, remount your receiver and position the switch and check for clearance. I would not attempt to install without using a drill.

Věděli jste?

Informace o výrobci

Odpovědný hospodářský subjekt podle nařízení EU

Brownells Arms s.r.o.
Bílanská 1861/81
76701 Kroměříž
Česká republika
info@brownells.cz

Jejda! Něco se pokazilo.

Narazili jsme na chybu při načítání obsahu. Obnovte stránku a zkuste to znovu. Pokud problém přetrvává, kontaktujte naši zákaznickou podporu.

Zpět na začátek