These steel die lock rings from Hornady clamp around the entire circumference of the die body. The lock screw squeezes the lock ring around the die with constant pressure across the threads - no jam screws. These rings have a flat on each side for wrench use. Sure-Lock Rings fit all standard 7/8""-14 reloading dies.
Další...
Tyto ocelové uzamykací kroužky na matrice od firmy Hornady svírají celý obvod těla matrice. Uzamykací šroub stlačuje uzamykací kroužek kolem matrice s konstantním tlakem napříč závity - bez zádržných šroubů. Tyto kroužky mají na každé straně plochu pro použití klíče. Sure-Lock kroužky pasují na všechny standardní matrice s rozměrem 7/8\"-14 pro přebíjení.
Další...
Hodnocení zákazníků pro položku HORNADY LOCK RINGS
Počet hodnocení: 6
Od brownells.com: 5
Průměrné hodnocení: 4,3
Vynikající(30.8.2019)
Naprosto přesná fixace matricí stačí dotáhnout nastavenou matrici matici rukou (současná manipulace dotažení klíčem a držení matrice je poměrně nesnadná vždy dochází k určitému pohybu matrice při dotažení) není potřeba klíčů a následně matici stáhnout imbusem (dotažení se vymezí jak proti závitu tak i k hlavě matrice, matrice je tak naprosto pevně fixovaná i v hliníkových hlavách Lee a Dillon, kde se standardní matíce se povolují.
excelent(28.7.2011)
this is an excelent replacement rign for any die set. you dont have to worry about stripping out the brass set screw like on other models and it squeezes the ring on the die instead of the screw contacting the threads of the die. because it isnt touching the threads so the set screw is made of steel and it will last you forever.
Great Ring(4.5.2012)
A good ring because you can lock it and also crank it down with wrench rather than having to mess with a channel-lock.
Works with Co-Ax press?(15.3.2013)
As stated in many places "works with Forster Co-ax press" NOT! Might be to a design change, but very sloppy fit in this press. Constant misalignment on smaller cases. Case mouth hits decapping pin assembly 90% of the time. Bought 10 of these with the press, my mistake.
All die makers should use this design(10.8.2014)
I have Hornady, RCBS, Forster, Redding and Lee dies on my bench. I have found over time that I prefer the Hornady locking ring design. The ring is easily tightened with the included hex key. This design tensions the entire bearing surface of the ring, rather than a single point-of-contact set-screw.
When I buy a new non-Hornady die, the first thing I do is replace the locking ring with one of these.
Hornady Die lock rings(25.7.2017)
Nothing bothers me more than poorly designed die lock rings. My past history of 45 years of reloading began with the old RCBS lead pellet/setscrew system that impinged on the 7/8-14 threads of the die making it very difficult to adjust or remove off the die. Advancements then used brass setscrews then angled split ring design at a tangent to the threads which adjusted themselves closed against the threads,a much improved version.These Hornady lock rings allow their propriatory red handled wrench to properly secure this split ring tightly against the press body. Other manufacturers use their wrenches but still use the old setscrew that crushes against the die threads. I recommend these lock rings over any other type to include "O" ring spongy attachments.
Produkt č.: 749000313 HORNADY LOCK RINGS Číslo výrobce: 044000090255440003 Tyto ocelové uzamykací kroužky na matrice od firmy Hornady svírají celý obvod těla matrice. Uzamykací šroub stlačuje uzamykací kroužek kolem matrice s konstantním tlakem napříč závity - bez zádržných šroubů. Tyto kroužky mají na každé straně plochu pro použití klíče. Sure-Lock kroužky pasují na všechny standardní matrice s rozměrem 7/8\"-14 pro přebíjení.
These steel die lock rings from Hornady clamp around the entire circumference of the die body. The lock screw squeezes the lock ring around the die with constant pressure across the threads - no jam screws. These rings have a flat on each side for wrench use. Sure-Lock Rings fit all standard 7/8""-14 reloading dies.
Další...
Tyto ocelové uzamykací kroužky na matrice od firmy Hornady svírají celý obvod těla matrice. Uzamykací šroub stlačuje uzamykací kroužek kolem matrice s konstantním tlakem napříč závity - bez zádržných šroubů. Tyto kroužky mají na každé straně plochu pro použití klíče. Sure-Lock kroužky pasují na všechny standardní matrice s rozměrem 7/8\"-14 pro přebíjení.
Další...
Hodnocení zákazníků pro položku HORNADY LOCK RINGS
Počet hodnocení: 6
Od brownells.com: 5
Průměrné hodnocení: 4,3
Vynikající(30.8.2019)
Naprosto přesná fixace matricí stačí dotáhnout nastavenou matrici matici rukou (současná manipulace dotažení klíčem a držení matrice je poměrně nesnadná vždy dochází k určitému pohybu matrice při dotažení) není potřeba klíčů a následně matici stáhnout imbusem (dotažení se vymezí jak proti závitu tak i k hlavě matrice, matrice je tak naprosto pevně fixovaná i v hliníkových hlavách Lee a Dillon, kde se standardní matíce se povolují.
excelent(28.7.2011)
this is an excelent replacement rign for any die set. you dont have to worry about stripping out the brass set screw like on other models and it squeezes the ring on the die instead of the screw contacting the threads of the die. because it isnt touching the threads so the set screw is made of steel and it will last you forever.
Great Ring(4.5.2012)
A good ring because you can lock it and also crank it down with wrench rather than having to mess with a channel-lock.
Works with Co-Ax press?(15.3.2013)
As stated in many places "works with Forster Co-ax press" NOT! Might be to a design change, but very sloppy fit in this press. Constant misalignment on smaller cases. Case mouth hits decapping pin assembly 90% of the time. Bought 10 of these with the press, my mistake.
All die makers should use this design(10.8.2014)
I have Hornady, RCBS, Forster, Redding and Lee dies on my bench. I have found over time that I prefer the Hornady locking ring design. The ring is easily tightened with the included hex key. This design tensions the entire bearing surface of the ring, rather than a single point-of-contact set-screw.
When I buy a new non-Hornady die, the first thing I do is replace the locking ring with one of these.
Hornady Die lock rings(25.7.2017)
Nothing bothers me more than poorly designed die lock rings. My past history of 45 years of reloading began with the old RCBS lead pellet/setscrew system that impinged on the 7/8-14 threads of the die making it very difficult to adjust or remove off the die. Advancements then used brass setscrews then angled split ring design at a tangent to the threads which adjusted themselves closed against the threads,a much improved version.These Hornady lock rings allow their propriatory red handled wrench to properly secure this split ring tightly against the press body. Other manufacturers use their wrenches but still use the old setscrew that crushes against the die threads. I recommend these lock rings over any other type to include "O" ring spongy attachments.