Přes 300 000 zákazníků - děkujeme vám!

40 000+ produktů pro lov a střelbu

Objímka hlavně 1911 od CLARK CUSTOM, ideální pro zbrojíře. 🔧 Snadná montáž a skvělá kvalita pro vaše potřeby!

CLARK CUSTOM STANDARD BARREL BUSHING

181001145

Atributy

  • Finish: Blued
  • Model: Government
  • Style: Drop-In
  • Typ zbraně: 1911
  • Dodací hmotnost: 0,018kg
  • Šířka přepravy: 83mm
  • Délka přepravy: 146mm

Detail produktů

Made in USA
  • Specifikace:
  • Finish: Blued
  • Make: 1911
  • Model: Government
  • Style: Drop-In
0 0 1 CZK

Neznáma dostupnost

Produkt č.: 181001145

Výrob. č.: CLK170575

Upozornit na dostupnost 899 CZK
  • Specifikace:
  • Finish: Blued
  • Make: 1911
  • Model: Government
  • Style: Drop-In

Popis:

Zobrazit originál (anglicky)
Zlepšete přesnost, eliminujte nadměrnou vůli
Standardní velikost, která pasuje na většinu hlavní s pouze drobným leštěním/úpravou. Plně opracováno. Oblíbený bushing zkušených pistolářů. Vyžaduje úpravu od zbrojíře.

SPECIFIKACE: .875" (22.22mm) dlouhé, .714" (18.13mm) O.D. Std, .575" (14.55mm) I.D.

Atributy

  • Finish: Blued
  • Model: Government
  • Style: Drop-In
  • Typ zbraně: 1911
  • Dodací hmotnost: 0,018kg
  • Šířka přepravy: 83mm
  • Délka přepravy: 146mm

Detail produktů

Made in USA

Recenze zákazníků

Hodnocení zákazníků (2)

4 / 5
Rozhodně doporučuji

Brownells USA Excellent product 5.11.2011

I use these bushings for both bullseye and game guns. In my opinion, its the best bushing you can buy. A lathe makes short work in the fitting department, and you don't have to use your barrel as a slide hammer.

Doporučuji s výhradami

Brownells USA VERY Oversized, tricky to fit. 1.7.2010

I purchased this bushing along with a Clark Custom 6" .45 ACP non-ramped barrel, to fit to a Caspian XR slide. I have used Clark barrels before with much success, so figured I'd give their bushing a shot.

The ID of the bushing where the barrel slides through has a LOT of material. As the description says, it is better for undersized/G.I. barrels, not a full-sized match barrel. It took a good while with an adjustable hand reamer to remove enough material to fit it to the barrel properly to a light drag fit.

Unlike most other bushings which are completely round on the skirt, this has 3 flanges that contact the ID of the slide where the barrel rides. I figured this would be easy enough, using the Brownells bushing mandrel to turn it down on a lathe. I cut the flanges until it would slide into the opening, yet I was still getting drag marks on the leading flange as I tried to twist the bushing into place with a bushing wrench.

Turns out the flanges are also oversized for the tunnel in which the lug rides, and on the forward edge of the lug as well as the outer surface of the bushing that contacts the slide. In all there are about 8 points of contact (including the ID where the barrel rides) to fit on this bushing. Very time consuming.

I have fit other manufacturers' oversized bushings, which tool much longer and served to build very accurate pistols. I'd stay away from this one unless you've got tons of experience or lots of spare time on your hands.

Věděli jste?

Informace o výrobci

Odpovědný hospodářský subjekt podle nařízení EU

Brownells Arms s.r.o.
Bílanská 1861/81
76701 Kroměříž
Česká republika
info@brownells.cz

Jejda! Něco se pokazilo.

Narazili jsme na chybu při načítání obsahu. Obnovte stránku a zkuste to znovu. Pokud problém přetrvává, kontaktujte naši zákaznickou podporu.

Zpět na začátek